Little CNC Machine: Difference between revisions
Jump to navigation
Jump to search
Sjefferson99 (talk | contribs) m (Added config example image) |
Sjefferson99 (talk | contribs) (Permitted items) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
=== Permitted applications === | |||
Extracted from manual, to be reworked into more definitive list. | |||
* Printed circuit boards and front plates | |||
** One sided and double sided boards | |||
*** FR3 | |||
*** FR4 | |||
*** FR5 | |||
*** G10 | |||
* Flexible substrates | |||
* RF substrates | |||
* Drilling test adapters | |||
* Structuring film patterns | |||
* Solder frames for PCB assembly | |||
* SMD fine line | |||
* Contour milling | |||
* Engraving front panels or labels | |||
* Depth drilling of rigid or flexible boards | |||
* Depanelling and reworking of populated and unpopulated boards | |||
* Machining of housings | |||
* Multilayer PCBs up to 8 layers | |||
=== Startup procedure === | === Startup procedure === | ||
The machine is quite picky about the startup order of operations, if you follow the below you should have success in loading the software with a good connection to the machine. | The machine is quite picky about the startup order of operations, if you follow the below you should have success in loading the software with a good connection to the machine. | ||
| Line 13: | Line 35: | ||
## Select "In the main clamp" | ## Select "In the main clamp" | ||
## Enter "1" in "Enter the free tool position" | ## Enter "1" in "Enter the free tool position" | ||
#Click OK on remove tool to toolbox | |||
#Machine will locate tool 1 then relocate to home and the software loads ready to use | |||
=== Troubleshooting === | |||
* No gas pressure | |||
** Connect gas hose | |||
** Ensure compressor is on | |||
** The gas pressure requirement is quite high, run the air to trigger the compressor to achieve sufficient pressure | |||
[[File:20240928 133608-min-min.jpg|thumb|Example configuration data]] | [[File:20240928 133608-min-min.jpg|thumb|Example configuration data]] | ||
Latest revision as of 16:05, 28 September 2024
Permitted applications
Extracted from manual, to be reworked into more definitive list.
- Printed circuit boards and front plates
- One sided and double sided boards
- FR3
- FR4
- FR5
- G10
- One sided and double sided boards
- Flexible substrates
- RF substrates
- Drilling test adapters
- Structuring film patterns
- Solder frames for PCB assembly
- SMD fine line
- Contour milling
- Engraving front panels or labels
- Depth drilling of rigid or flexible boards
- Depanelling and reworking of populated and unpopulated boards
- Machining of housings
- Multilayer PCBs up to 8 layers
Startup procedure
The machine is quite picky about the startup order of operations, if you follow the below you should have success in loading the software with a good connection to the machine.
- Power the 4 way strip
- Ensure the compressed air connector is connected and pressurised
- Power on the PC if off
- Switch OFF the mill at the switch to the right by the power connector
- Load the Boardmaster software from the shortcut on the desktop
- Splashscreen appears - wait for 10-20 seconds for the connection failure dialogue to appear
- Ensure COM1 is selected and power on the CNC
- Select connect
- In the dialogue that appears:
- Select "In the main clamp"
- Enter "1" in "Enter the free tool position"
- Click OK on remove tool to toolbox
- Machine will locate tool 1 then relocate to home and the software loads ready to use
Troubleshooting
- No gas pressure
- Connect gas hose
- Ensure compressor is on
- The gas pressure requirement is quite high, run the air to trigger the compressor to achieve sufficient pressure
